Replacement Seals for Flygt and Grindex Pumps NO PUMP MODIFICATIONS NECESSARY NO SPECIAL FITTING TOOLS REQUIRED.

This product is in stock, we can ship them right away once the payment has been verified

The Grindex 50 538 00 (Upper Seal) is a seal, which can be categorized as a pump seal. It is an alternative to the  AES T05Z, Flygt 713 90 00 and Grindex 50 420 00 (Lower Seal). It is suited for the Flygt 2730 (Pump), Flygt 2740 (Pump), Flygt 2750 (Pump) and 46 others. 

This seal replace original Flygt seal and use for Flygt pump no:Grindex Maior,Master,Matador,Midi,Minette,Salvador.AES T05Z.

Delivery time  :  3-5days 

Our pump seals thrive under pressure.

Whether you need a new seal or you have a seal to be repaired, we welcome the opportunity to help you with your rotary sealing needs.

Contact us to check the details such as alternative material and dimension or cross section drawingTo ensure that the seals will meet these requirements, We has chosen to design and manufacture its own Flygt seals. As these seals are designed solely for use in submersibles, there is no need for compromise, and seals can be fully optimized for this single purpose.

A mechanical seal is a very effective device. Every centrifugal pump must accommodate a spinning shaft while mechanically maintaining fluid or gas contained in the "wet end" of the pump. Mechanical seals consists primarily of a rotary seal face with a driving mechanism which rotates at the same speed as the pump shaft, a stationary seal face which mates with the rotary and is retained using a gland or in some pump models an integral stuffing box cover, a tension assembly (utillizing springs or a metal bellows) keeps the rotary face firmly positioned against the stationary face preventing, excluding, and containing contamination and leakage, both when the pump is not in operation and when the pump shaft is rotating. Static sealing gaskets, orings or elastomeric bellows are strategically located to complete the seal assembly.

We offer quality sealing and cost-effective mechanical seal designs that help keep equipment running longer while reducing downtime. Through our comprehensive selection we provide mechancial seals with short lead times and with a variety of designs for use in many common and more challenging industry applications. When selecting a mechanical seal, it is important to know what sort of design is needed, and we have outlined a few of the more common elements below.

In-line Seals
In-line Seals simply refers to seals that are mounted to a shaft or sleeve but are mounted independently as individual parts.    

Single Spring Seals
Mechanical seal designs range from the work horse "single spring" mechanical seals,
to highly engineered double cartridge seals for extreme applications.

PTFE  Seals
PTFE (polytetrafluoroethylene)or as most people know it Teflon ® , has a 0-14 ph range it usually will hold up.  

Outside Seals
outside Mechanical Seals can also be used in equipment with stuffing boxes which will not accommodate inside seals, and they are easier to access for adjustment and trouble-shooting.

Single Cartridge
A Single Cartridge Seal is a pre-assembled package of seal components making installation much easier with fewer points for potential installation errors to occur.

  
Metal Bellows Seals
Metal Bellows Seals for pumps - The most common are AM350 and Hastelloy C. Usually with Stainless Steel end fittings permits these mechanical seals to be used for services beyond the range of mechanical seals with synthetic rubber sealing members.

Tandem Cartridge
There are two basic double seal arrangements: Tandem Cartridge and face-to-face. A double cartridge mechanical seal can be configured in either configuration.
Double Cartridge
Double Cartridge Seals - Tandem Cartridge Seal is a pre-assembled package of seal components making installation much easier with fewer points for potential installation errors to occur.

Seal Pots
Mechanical Seal pumbing plans you will know in some cases you will need a Seal Pot to supply clean lubricating fluid to your seal.    
Mixer and Agitator Seals
Mixers and Agitators Seals offer a unique problem for mechanical seals. Because most mixers or agitators are mounted on top or on the side of a vessel the long shaft being used to mix or agitate usually has an issue with run out.
Mechanical Seals - Face Materials
Mechanical Seals come in a wide range of designs however the most important factor when determining how long a seal is going to last, is deciding on the right seal face materials. The old adage "pay me now or pay me later" applies to seals. You must consider the environment the seal will be exposed to. Abrasive environments

require seal faces that will hold up to the wear and tear of abrasive environments. It makes little sense to save money on the seal only to have to spend more money to replace the seal later. On the other hand if you are pumping very clean fluid that has a lubricating quality such as machine oil or Ethylene Glycol, save your money

for better quality bearings.

Seal Faces:
Ceramic - Generally a 99.5% aluminum oxide offering excellent wear characteristics due to it's hardness. It is chemically inert and can be applied to nearly any product. Ceramic cannot however handle the thermal shocks that Ni-resist or 17-4 seats can. They will also shatter like a plate if dropped on concrete.

Silicon Carbide - Is a bluish-black material created by fusing silica and corbon. It is in the same family as Ceramic (due to the Silica), but has much better lubrication qualities and is harder. The most common is reaction-bonded silicon carbide. In Chemical applications however, Alpha Sintered Silicon Carbide may be
recommended. Alpha Sintered Silicon carbide does however sacrifice the Pressure Velocity ratios due to the lack of un-reacted free carbon. Either grade of SIC can usually be re-lapped and polished to be reused.

Tungsten Carbide - A very versatile seal face like Silicon Carbide. It is very hard like silicon carbide however it is very heavy to the touch, making it easy to distinguish from silicon carbide. Ideal for high pressure applications due to a high modulus of elasticity which helps prevent face distortion. Tungsten carbide also can be re-lapped and polished to be re-used.
Ni-resist - Is a form of Stainless steel which has had nickel added to it to lower the friction generated by the rotating face. it is an inexpensive seal face and ideal for fresh water applications.
GFPTFE - Say that one ten times.... Glass Filled PTFE (most people just say Teflon (R)). Gives the chemical resistance of PTFE however glass must be added to give the face hardness and to prevent cold flow issues associated with PTFE.
What is more, we can supply many many types replacement seal of :
eagleburgmann AX05/AX25/AX40K/BT-A2/BT-AR/BT-PN/CARTEX DUAL SEAL/CARTEX SINGLE SEAL/CARTEX ANSI SINGLE SEAL/EA560/ED560/EHJ/EK700/EMG1/EMG2/EMG12/EMG13/H3B/H7N/H12N/H74D/H75VK/H75VN/HA211/HJ92N/HRN/LB500/LP-D/LP-S/M2N/M3N/M7N/M74D/MF95N/MFL85N/MFLCT8/MFLWT8/MG1/MG12/MG13/MGS1/MG9 and so on.

Johncrane type 4610/4620/5610/5610Q/5610L/5620/type 1/type 2/type 21/type 20/2100/2100k/2100n/2100l/58B/59B/58U/59U/JCS1/JCS2/SB1/SB2/SB1A/SB2A/SBW/SE2/SE1/TYPE 502/515E/609/670/675/676/680/10T/10R/TYPE 20/20R/WB2/9T/8-1/8-1T and so on.